Fanuc oi-MD program not TO display,parmeter?
I HAVE BEEN USING A FANUC 21-i controller,to keep it short, i now run Oi-MD. so...what is the equivelent to parameter #3232 for my Oi-MD?anyone that can read can figure out how to change psr(bit#6)...
View ArticleClik here to view.
Each Pass Moves in -X Direction Causing Stair Stepping
If I carve a 3d rough out each pass moves in -x direction resulting in a stair step. At the end of the process router is instructed to return to origin. It moves past the origin anywhere from .25 to 1...
View ArticleMacome mag sensor orientation
Does anyone know the correct orientation of Macome mag sensor MG-1378-BS? I see there is a N (north pole) and S (south pole) markings located on each end. I'm just trying to make sure I don't have it...
View ArticleFanuc OM-C spindle orientation parameter
Hi all. Can someone tell what parameter on a fanuc OM-C adjusts spindle orientation? I need to adjust the spindle about a 1/4 turn and the fine adjustment on the spindle orientation board I know is for...
View ArticleClik here to view.
How to deteck broken tooling in FANUC15B
Hi! Can anybody help me with G code or Macro with detecting broken tool? The device does it is in the photo. The CNC FANUC 15B Please help. Regards, Attached Images IMG_1541.jpg (702.1 KB)
View ArticleFANUCROBOTDRILL MACHINE T14i CONTROL FANUC16iM
Dear sir, good evening , i have one problem of fanucrobotdrill machine alarm SV465 (X) AND (Y) READ ID DATA FAILED. this problem after repair the power supply unit ,machine power on alarm SV465. i need...
View Articlemakino pro3 tool monitoring
I can bring up a tool life page with tool monitor amp usage also but when I put values in I can't get them to turn on like I do with tool life. The screen shows a study mode,ac mode and sl mode but...
View Articleaxis drift, electrical, or software?
I have a cnc gantry style router, that was retrofit with camsoft cnc professional software. When I run a series of plunged holes, to test repeatability, the holes oblong, and get a little deeper every...
View Articlemazak mazatech 630n b axis lekage problem
mazak mazatech 630 n hmc machine b axis lekage problem at the time of pallet clamping
View ArticleER97 IO link failure (ch1 group2)
hi everybody, today we have one problem on Gleason 600 HC Hypoide gear cutting machine, which is having Fanuc 160i-mb controller. we found alarm "ER97 IO Link failure (CH1 Group 2)" then we had done...
View Articleamada pega 357 and fanuc
Dear Sirs, Is anywhere avaliable some circuits, that I can check at least voltages on fanuc controler ? Controler was not grounded and when worker connect a drill machine to Amada socked, the...
View ArticleIts a parameter thing!
I NEED HELP PROTECTING MY PROGRAMS FROM DISPLAY, I RUN FANUC OI-MD CONTROLLER, YES I KNOW #3202 NE9, #3210 PASSWORD FUNCTION, BUT THEY WILL STILL DISPLAY! BACK IN THE DAY(21i THAT IS) YOU COULD USE...
View Articleinterlocks
is there a door interlock out there that still allows a cnc programmer to do his set ups [opening and closing the door as needed] then activating after set up is complete? so it is safe for an operator.
View ArticleAutomating a Pause / Resume for NC Program
Is it possible to automate a Pause and Resume? I would think inserting an M01 would Pause the program, but how to automate the Resume? Perhaps the CNC Machine tools PLC could initiate the command???...
View ArticleMachine heat, sink fin.
I am machining some copper warm sinks. These are off the display areas, being modified. I have nine to machine. I am just including some gaps, and need to machine the bout for approval on one end. The...
View ArticleStepper motor not driving but there is power
I try setting up my own Cnc machine,but the challenge am facing is that the the stepper motor could not drive properly, is as if is not getting enoughPulse, if I try to control it with keyboard of the...
View Articlematsuura spindle problem
Hello folks. I'm working on a matsuura vmc 510 with a yasnac controler. When I turn on spindle say ccw At 500 rpm. It comes on for a second then switchs to 2700 and cw. No error or alarms are given. It...
View ArticleHitachi Seiki HG500 Position Module B axis
I have Hitachi seki CNC with a pos-M 10-22-00 Position module and led 7is flashing red and led 8 is on I do not have any documentation on this unit had the the motor for B axis rewound due to an open...
View Articlefadal EMC 7.5 hp 7500rpm spindle drive
we have three fadal emc units at the end of june the first two went down .I was able to find two of the Yaskawa CIMR -V7 AM25P 51 drive units . 1 1/2 wks later the third unit went down have been...
View Article