Kitamura with a blank crt screen
CRT screen is dark. Is there a power save or a way to manually turn the CRT screen on & off? Or is there a way to test the crt?
View ArticleEmach-Eding USBCNC-MOTION drivers-No holding Torque on stepper motor.
We've got an Emach machine here controlled by USBCNC software/controllers and MOTION MSD542 stepper motor drivers. The Y axis has two stepper motors driving it, one as a slave. One of the stepper...
View Articleamada vipros 255 turrit punch
Hi everyone im needing help with an alarm code #2095 just says CENTER FREE BER. (OFF) LOWER LS AMADA VIPROS 255 WITH FANUC SERIES 18-P CONTROLLER
View ArticleAttention Please Need help with chatter boring carbon steel please READ and...
Hello, I am having a hard time finding any help with chatter anywhere, I would of believed it is talked about all the time, go figure my luck. Anyone that can help take a look at my basic setup and...
View ArticleExperienced CNC Mazak Lathe programmer/set-up/operator seeks employment in...
I Have 30 years machining exp. However as an ex-offender I am having trouble finding someone to give me a chance. I have been programming and setting up CNC MAZAK LATHES for over 20 years as well as...
View ArticleCNC Mazak Lathe Programmer/Set-up/Operator seeks employment in Florida
I Have 30 years machining exp. However as an ex-offender I am having trouble finding someone to give me a chance. I have been programming and setting up CNC MAZAK LATHES for over 20 years as well as...
View ArticleNeed Cincom L16 & Meldas 320' parameters
Hi, All. Looking for parameters (including options) of the lathe: Citizen Cincom L16 & Meldas 320 (with MC161-1 card). Manufactured in 1992. I will be glad any their view: scans from the hard...
View ArticleHitachi VK45 won't run in AUTO mode
Machine specs: VK45 (Seicos M II) Micon 16 Version 5.0 Seicos M0290 Ya'll may have noticed from my prior post that I had a problem with the Fanuc spindle drive on my machine. Well after months of...
View ArticleBar Feed on Mazak Problems
I have a Mazak quick turn Nexus 250 II with a LNS Quick Load 80 bar feeder works great lathe runs great but when the lathe sees the end of bar at the M69 it jumps to the sub program 9999 it will run...
View ArticleMITSUBISHI SPINDLE DRIVE MDS-C1-SPM-260 Alarm 32 (IPM detects over current)
Dear Friends, We have a Mori Seiki SL 204 CNC Lathe with MAPPS MSG-501 Controller. Spindle and Servo Amplifiers are MDS-C1-SPM & MDS-C1-V2 Series from Mitsubishi. Occasionally during CNC operation,...
View ArticleDisk cloning program for CNC machine hard drives
We have Agie Wire EDMs and DMG 5 axis cnc mills. We are trying to make a clone copy of their hard drives. We have replacement hard drives. Which is the best software program to clone these hard drives?...
View ArticleYAng SML 20 Fanuc ot-d
Just got this machine need some help parameters ??? anyone ?? turret not in sequence?? lost my drives and hydraulics while working on it they dont want to come back up Appreciate all help thanks Capt Bob
View ArticleHeidenhain compensation parameter
I have the following problem on a Johnford VMC 850 machining center , fitted with a Heidenhain i530 control. Placing a clock on the table surface and moving the table in the Y axis , we get a...
View ArticleHello.
My name is Kernald parslay i am a new membere here. I've been working in the CNC world, for about 2 1/2 years and have 27 prior years experience in aircraft maintenance. I am looking to gain, as much...
View ArticleMiyano Slant Bed Taper Problen
I have a Miyano JNC -45 slant bed that has a taper in the cut. The pages needed in my manual are missing for this proceedure. Does anyone have a copy of the pages or has experience in this? Thanks
View Articlekia turn 21 lost parameters
machine is dead. lost its parameters and I didn't get chance to back them up is there anyone that has a copy of the parameters for a kia turn 21 lathe with fanuc O-T controls.
View ArticleHelp Needed
My father recently passed away (2010 - but feels like yesterday) and unfortunately prior to his death much of his tools disappeared. However, I have attempted to inventory some of his heavy machinery...
View ArticleHello from Southern California
Hello All, What a great resource this site appears to be, thanks for letting us join! I run a small fabrication shop in La Habra, CA. We just purchased 2 CNC machines (lathes) so we are in the process...
View ArticleGetting programs into Fanuc 3t and 6t
Hello All, We just purchased 2 old CNC machines (lathes) now we are in the process of trying to get up and running. I have a programmer/setup person, but he has no experience with the old machine...
View ArticleMitsu Seiki VM w/ Fanuc 6MB2 Control - RS232 Communication Trouble
Hi all, new member here. Have been lurking for about a week trying to search and read as much as possible to see if i can figure this out myself, and cant. So we have just moved locations and have...
View Article