Strange intermittent backlash
Hi all, I'm having some trouble with my CNC going a little haywire when it is cutting. I'm cutting various shapes of different sizes out of 4mm plywood using a 2mm dia. 2 tooth endmill and stepping...
View ArticleNew Member/CNC Selection
Hey everyone, I just joined up. I am a retired machinist and want to do woodworking via CNC. I have looked at all kinds of machines. I am curious as to what you folks would recommend. I want to machine...
View ArticleJust Joined Up
Hey everyone, I just joined up. I am a retired aerospace executive, that started as a machinist, worked in engineering, and then went to school to get my degrees. Now I want to do woodworking via CNC....
View ArticleLoad the Parameter O-C
Hello Forum, My name is Diện, Iam From Việt Nam, i service for AMADA machine, i see in the web https://www.youtube.com/watch?v=eK7A1pvwdII tech to load the parameter, but i thinks you must change the...
View Articlefirst posting, finding ballscrews
Hello All, I've come across a number of older smaller machines 5' lathes/milling machines which need new ballscrews. I'm accustomed to running to the manufacturers for ballscrew/ thrust bearing...
View ArticleNew kid on the block
Hello It's great to be here! I'm Doug. I'm the Training Coordinator at Doosan Infracore America as well as Applications Engineer there. I also have a small machine shop - Franklin Lakes Machine Co....
View Articlehelp with a hurco cnc
i have a hurco cnc vertical machine center eq001 that i need to find a quill seal for. we had a machine repair man here but he is having a time finding the seal. the best measurments i can get at this...
View Articlescott abshire
good day to all, ive got a mori nt that all the sudden the macine is magnetized the chuck steady rest tail stock and part running, at a loss on this have checked the spindle motor alls well on that end...
View ArticleClik here to view.
How To Maintain And Clean Your Glass Machinery?
Hello Guys, Do you have troubles in cleaning and maintain your glass machinery? I do have! Here following are some of my ways to deal with the problem, if you have better ways to do it, please share...
View ArticleClik here to view.
Glass Washing Machine Good For Glass Cleaning
Hi Guys, Glass washing machine as one glass processing equipment is well designed and used for washing and cleaning the flat glass, which is easy to use and raise your working efficiency on cleaning...
View Articledischarger smoking and leaking a fluid. what caused this and is it toasted?
this item is in a 1993 leadwell 760. wiring seems to be correct 220 3 phase. new hookup. if I replace this item what else to be concerned about?
View ArticleIndramat Servo Motor is good or bad?
I want to buy Indramat Servo Motors. I dont know it's good or bad. Please give me your feedback about Indramat.
View Articleallarm over travel fanuc 15t
Hi, I have a lathe fanuc 15t, a friend of mine has canceled the parameters of the machine and now the x-axis to make blind holes the machine does not go to zero but the only iron that I use to make a...
View ArticleHydraulic platform lift-10m
Model: TAM0.2-10 Features: 1. Hydraulic platform lift is mainly used to lift workers to higher places for maintenance, cleaning or installation. 2. It is characterized by manual move, portability and...
View ArticleFanuc w3 paramaters
Hello guys,i dont know is this wrong place but i'm asking for paramaters fanuc tape cut w3 ..we lost all after sysem was down,now we dont have backups,someone got it to send me ? thanks
View ArticleDo you use G73 on a Fanuc lathe
How do you machine a job with a non-monotonic variation in surface profile, i.e., with radial or axial undercuts, if Type II G71 / G72 cycles are not available? May use a CAM software if you have...
View ArticleOkuma LB15 (OSP5000) lathe drive fault
Hello All, We have a problem with an Okuma LB15 (OSP5000) lathe, any advice would be much appreciated. - On start-up the machine boots to the main screen but often with Alarm 201. The Okuma manual...
View Articleservo alarm # 401, # 414. Mori Seiki SL 25
Hello, we have the following alarms on our Mori Seiki SL 25. Servo alarm 401, 414 as soon as turn on machine. DGN 720 has bit # 4 (1), (abnormal current alm). We swapped the servo amplifier with a new...
View Article