Mori Seiki TL40 Fanuc10TF Tool setter problem
Got this TL40 lathe with the batteries flat and the parameters lost. Mori did not have parameters for my machine but supplied a global data list. Installing pmc and nc parameters got the machine...
View ArticleMillPWR Help
I just took delivery of an older (early 90's) Bridgeport with a MillPWR 2 axis control. It was working fine. I powered it down. It sat for A week or so then up in attempting power up, it have me an...
View ArticleJohnford SL-800B False overtravel
Hi all, this machine has began to have a problem with the hydraulics turning off during cycle. The only thing I see on the panel is the over travel indicator is lit while both turrets are actually in...
View Articleciao a tutti
Hi everyone, Im Machine Tools Italy www.machinetools.it see you in forum and best regards!
View ArticleAmada Vipros 345 Queen ( Year - 1997 ) axis speed too fast to run
Good morning all, I have got a problem with my Amada Vipros 345 Queen ( Year - 1997 ). I am using PEUWin dnc software for program upload and download. Electrical power broke down while a program was...
View ArticleClik here to view.
Hitachi VK45 5065 TF START ALARM
Getting this error on my VK45. 5065 TF START ALARM What is a TF? Anyone know what this abbreviation stands for? I have tried tracing it back in the ladder program (I am far from an expert doing this)...
View ArticleOkuma Mill mother board battery change
Hi Need to change the back-up battery on Mother Board 3 on a MCVA II vert. mill. It says not to shut power off, can I pull mother board out with power on ? Will I lose any info changing this ? Should I...
View ArticleCNC Plate rolls
Hi.. I have a CNC plate rolls, AHS 30/40. it can't started becouse some trouble in relay, I think, couse the display says : - Thermic relay waste - Control panels key is not active - Phase line relay...
View ArticleRelay Problem
I have a CNC Plate Roll, Akyapak AHS 30/25 It can't be running and the monitor says : - Thermic relay waste - Control panels key is not active - Phase line relay not active - Emergency relay not active...
View ArticleFanuc 10M Mother board short 5v to 24v and both to ground?
Blown fuse 5a and 3.2a Got it down to mother board and found Short between 5v to 24v and to ground. Anybody have experience with this? Maybe a common component that shorts? Board is A16B-1010-0190-05B...
View ArticleFanuc 10M Mother board short 5v to 24v and both to ground?
Blown fuse 5a and 3.2a Got it down to mother board and found Short between 5v to 24v and to ground. Anybody have experience with this? Maybe a common component that shorts? Board is A16B-1010-0190-05B...
View ArticleHitachi Seiki HT20-300 restore parameters
I have trouble with lathe Hitachi Seiki HT20-300 (1986year) with FANUC 10t. The NC battery was disconnected while machine power was off. So all NC data was lost and now restore NC data (SRAM, NC...
View ArticleToyoda FHN 50II
Hi. Does anyone have any experience with a toyoda FHN 50II where the pallet will not lock into position so the part can be loaded? The air keeps running and will not let the pallet set into locking...
View ArticleHarmonics on Spindle Race/Bearing from drilling
Facing/Boring/Drilling/ multiple ops on Meat Slicer Basins using 2 Pallet, Okuma MH60, horizontal 50T, probably 5000/6000 Series aluminum alloy causing a high pitched squeal/chatter while routing a...
View Articlefeed rate changing after spindle stop
Hello Chaps I am using mach3 on a home made lathe. I am having a problem with the feedrate in the setup string i set f=.1 ( I am working in mm) when i use G0 - the machine feeds at a reasonable fast...
View ArticleFuse on dc link blown
HI, anyone can help solve this problem >9003 SPN 1:FUSE ON DC LINK BLOWN >9051 SPN 1:LOW VOLT DC LINK >433 Z,X AND Y AXIS:CNV.LOW VOLT DC LINK
View ArticleFuse on dc link blown
Anyone can help me solve this problems >9003 spn 1:fuse on dc link blown >9051 spn 1:low volt dc link >433 x,y and z axis:cnv.low volt dc link
View Articleservo alarm
Hi All, I have a servo alarm #603 y axis inv ipm alarm. I replaced the servo drive A06B-6111-H205, 2 axis module MDL SVM2-20/20i last week because the C-axis had a 449 c axis inv prm alarm. Both times...
View ArticleHi All
Hi All, I'm looking for project ideas for some at home welding projects. I also enjoy working on cars and boats when life gives me the time. I get a lot of my materials from buymetal.com and thought it...
View Article