Clik here to view.
Circular interpolation, tons of flat spots
Hello all, my first post here. I'm extremely new to CNC repair & diagnostics and I'm hoping someone can help me. At our plant we have a mill that is cutting many flat spots as it does a circular...
View ArticleParameter Setting for Setting a Live-Tool Maximum Speed
Hey all- I have a Fanuc 18i-tb control on a Hyundai-Kia SKT210sy CNC Turning Center. The data printed on the live-tool blocks say they will run at 5000 rpm but I can't seem to get them to turn any...
View Articlemori seiki sl-25 lathe trouble
hello,i have a mori seiki sl-25 lathe it runs fine in auto when running program but when you go to manual the hand wheel will only make the axes move in Z axes, if you put it in X axes the hand wheel...
View ArticleHello New here
Hello ,i'm new here, from switzerland, a cnc machine hobbyst,i'm very excited to be part of the community, to share and learn from all of you.
View ArticleBrother TC-221 Error 6 ROM error
I have a Brother TC-221 and I am getting an "Error 6 ROM Error" at power up. The backup batteries have died. Is this error due to the dead batteries? Do I have to re-enter the parameters? How do I do...
View ArticleNiigata HN100B lost program for toolchange
Hi all, I have a problem with Niigata HN 100B Fanuc15-MA. We lost programs for palletchange and toolchange 09000. We did not have backup of programs. It would be possible to send me these programs?...
View Articlewriting parameters on yasnac i80L
Hello, I'm new to this forum and figured I give a try to trying to find someone who knows how to write a program that will change the bit/value of a parameter in a yasnac i80L controller. I am trying...
View Articleyasnac i80L parameter writing
I am trying to write a program for my Hitachi-Seiki HT20SIII so that I can change the bit status of a parameter. I am tring to change parameter #7102 (keep relay) bits 3, and 4 under program control...
View Articlehow
96×48"inch wood engraving area which stepper motor suite for for this any one plz give me idea for making home build cnc step by step guide for wood engraving
View ArticleEcoca EL-4610E: Mitsubishi -Z70- Absolute Position Error Alarm number 0001.
Hello! I have run into a spot of trouble whit my Ecoca lathe, I get this alarm: "-Z70- Absolute Position Error Alarm number 0001." and when I refer to my machine manual it tells me to consult the...
View ArticleNew member
Thanks for allowing me to use the site, much good information has been found here! I work at a plant that has many machining centers that produce engines.
View ArticleSinumerik 810M GA 1 - shut down instantly
Hello, I have a problem with Sinumerik 810M GA 1. The machine worked with no issues untill today when it stopped. Fans are working good but the monitor and whole system is OFF. Is there anyone, who had...
View ArticleFanuc 0iTF
Hello All. I have just joined this site. I have a Fanuc 0iTF controller on a Vertical Boring Mill. This controller does not recognise G90 commands. How do I do a canned cycle using this controller?
View ArticleDuraturn 2550 foot switch failure after machine move
We have 2 Duraturn 2550 machines that were moved from one plant to another. After getting them back up, on one, the X axis would not move and the chuck would not function with the foot switch. The...
View Articlemaho mh500w cnc232b upgrade
dear all we had that machine MAHO MH500w WITH CONTROLLER HEIDENHAIN CNC 232 B NC SOFTWARE 242940 08 PLC SOFTWARE 250134 04 the problem we face is that we can not add programs from modern cad cam...
View ArticleDo the Cincinnati Arrow 500 & Arrow 750 use the same pendant ?
Hi, Hopefully somebody can answer this. Do the Cincinnati Arrow 500 & Arrow 750 Vertical Machining Centers use the same pendant ( P/N: 3-424-2227A) ? If not, do you know what Pendant P/N the Arrow...
View ArticleAmada machine with ^6M controller
I have cnc tpp make Amada, while doing ref. T axis ref. complete light not coming, hence auto mode is not running. can some help,
View ArticleCtek KM-100D parameters
Good day. I am looking for advice as to how to get into the parameter setting on my machine.I need to do the backlash settings as I have already adjusted the backlash machanicly.
View ArticleIntermittent Vibration at Spindle Start
Hi All.. Working with a KOMO VR510 Router that intermittently starts to vibrate like crazy in CW spindle direction after a tool change or when the spindle starts. We are sometimes able to correct the...
View ArticleFanuc series 18-P
Good evening all, I work in the maintenance department of a large manufacturing company. We have an Amada 1010 BLS with a Fanuc series 18-P control. Tonight the control gave an error 1300 watchdog...
View Article